Below are Delta "Cabinet" style tablesaws for sale. A tablesaw is usually the cornerstone of a shop, so choose a good one to build your shop around. Plan ahead! If you plan on only dabbling with small crafts and knickknacks then you should be fine with a smaller and cheaper model, but serious woodworking and furniture building will be much more fun (and easier) if you have a bigger 3-5hp 10"-12" cabinet model tablesaw. The "Cabinet" models are the bigger and more reliable saws, the big brothers to other models. If you can afford a cabinet version, I highly suggest you spend the money now on a cabinet saw and save yourself the hassle of upgrading later on. But remember to check your wiring in your shop as most of these cabinet saws require 230 volt service.

Go to:
Delta Portable Tablesaws
Delta Contractor Tablesaws
Delta Cabinet Tablesaws

Delta 36-843 "Limited Edition" 3 HP Unisaw with 50" Biesemeyer Fence

Among serious woodworkers who demand top quality tools in their shop, there's no debating the desirability of a Delta Unisaw. It's one of the few cabinet-style table saws still made in the USA, and the benefits show up in the quality of the tool's workmanship and finish. The Unisaw's smooth operation can be traced to the widely spaced, massive trunions which are machined from fine-grained cast iron and are completely adjustable to ensure the best possible alignment. The heavy cast-iron table adds to the saw's stability and features a 3/8-by-3/4-inch T-slot on each side of the blade. Include the two extension wings and you have a generous cast-iron table surface of 36 by 27 inches.

The single-phase, 3-horsepower induction motor is housed in a dust-sealed, fan-cooled enclosure, and power is transferred smoothly and efficiently via a positive-traction three-belt V-drive system. The motor cover has handy storage slots for your miter gauge and table inserts, but more importantly, the inside is designed to maximize the airflow for dust collection and, in conjunction with the redesigned cabinet interior, funnel all the dust efficiently to the 4-inch dust port without a hitch.

This model comes with a 50-inch commercial Biesemeyer fence system and accompanying table board. While the basics of this popular fence design have been copied by competing saw and fence manufacturers, there's still nothing quite like the original. The Biesemeyer is made of the heaviest gauge steel we've seen on a T-square type fence, and the fence face itself is made of laminated 9-ply Finland birch, glued solidly in place--a construction method that eliminates warpage in the fence line that the bolts or screws used in competing systems can cause. The fence locks to the front guide rail using Biesemeyer's three-point locking system and automatically aligns the fence parallel to the blade when the lever is tightened down, providing reliable accuracy every time. --Brian Trinen

Delta 36-821 Special Edition 10" Tilting Arbor Unisaw with Biesemeyer 50" T-Square Commercial Fence

Setting the standard since 1937, Delta's Unisaw has many features that make it the choice for serious table saw users. Powered by a three-horsepower, single-phase induction motor, this saw cuts smoothly and cleanly. A triple V-belt drive connects the motor to the arbor eliminating belt slippage and vibration while making use of all of the power from the motor. Supporting the motor and arbor is a set of widely spaced, massive, cast iron trunnions that are adjustable to maintain perfect alignment. The saw arbor flange is face machined after assembly so the blade runs perfectly true. Blade height and angle are easy to adjust with the convenient hand wheels located on the front and side of the cabinet. For consistent results, the hand wheels have center locking knobs that lock the adjusting mechanism to prevent movement. Angle adjustments are quick and easy with the adjustable positive stops for 45 and 90 degrees. The miter gauge rides in T-slots in the table which support the gauge beyond the front edge of the table, allowing cut off work on wider stock. The included Biesemeyer fence has a hairline pointer and built-in tape measure for easy, precise set up. A three-point locking system keeps the fence parallel to the blade for accurate cuts. With these features and others like lubricated-for-life ball bearings and precision bored bearing seats, this saw is built to last. Extension table (pictured) is sold separately. Two-year limited warranty on machines, parts, and accessories. Includes saw, cast iron extension wing, miter gauge, blade, blade guard, fence and miter gauge storage hooks, and 50-inch Biesemeyer fence.

Delta 36-R31X-U50 X5 3HP Right Tilt Unisaw with Unifence

A 5 year warranty, one of 4 free tools or a $50 rebate, up to $500 in accessories, & over $2000 in savings with X-treme savings book. This is the model that started the Unisaw's famous reputation for unequaled quality. The 3 hp single phase unit boasts a new-age computer designed motor cover, which incorporates a new and improved dust efficient design with integral 4" dust connector. The blade is driven by a three belt system that virtually eliminates deflection and vibration. Compliment this icon with a 50" Unifence saw guide that blends accuracy with versatility, add an Industrial Carbide-tipped blade and two 10" cast-iron wings and it is easy to see why this Unisaw is the "Standard in the Industry"

Delta 36-L31X-BC50 X5 3HP Left Tilt Unisaw with Biesemeyer

A 5 year warranty, one of 4 free tools or a $50 rebate, up to $500 in accessories, & over $2000 in savings with X-treme savings book. If bevel ripping single-sided laminate is in your near future than this is the saw for you. A left tilt version of our famous Unisaw, this 3 hp single phase unit boasts a new-age computer designed motor cover, which incorporates a new and improved dust efficient design with integral 4" dust connector. Add a 50" commercial grade Biesemeyer fence system, Industrial Carbide-tipped blade and two 10" cast-iron wings and it is easy to see why this "bullet-proof" Unisaw is the "Standard in the Industry"

Delta 36-L31X-U50 X5 3 HP Left Tilt Unisaw with Unifence

The X5 is one of the finest pieces of machinery we've seen. It's the left-tilt version of Delta's magnificent Unisaw, and everything from the motor to the finely machined T-slots is of the highest standard. Take the motor, for example. It's a 3 HP, single phase 230-volt with full-voltage starter. It flawlessly powers a positive-traction, three-belt V-drive that runs between two massive lifetime ball bearings for no--and we mean zero--vibration. The table is cast-iron, smooth as glass, along with two cast-iron extension wings and a beautifully laminated table supported by rock-solid, leveler-footed steel legs. Riding along the huge 76-by-27-inch table surface is a 50-inch Unifence guide with an adjustable flip-stop; if you've ever used one, you know the precision. It glides like it's on air and locks down with not a hair's breadth of error, even at its maximum 50 inches to the right of the blade. Even the arbor is a piece of perfection, precision-ground, stress-proofed and flange-faced after production. Inside this 600-pound saw's cabinet is a clever slope that directs sawdust right to the 4-inch duct collector chute to eliminate clogging in the cabinet. Quality saws always have a T-slot for the miter gauge, and this one's no exception, allowing you to extend Delta's super-precise Auto-Set miter gauge far beyond the front edge without tip-out or instability on both sides of the 10-inch blade. The left-tilting arbor allows you a max cut of 2-1/8 inches at 45 degrees, putting big gorgeous bevels well within your reach. If it's precision and power you're after, this is the last saw you'll ever buy.--Kris Jensen-Van Heste

Delta 36-R31X-BC50 X5 3 HP Right Tilt Unisaw with Biesemeyer Fence

The X5 is one of the finest pieces of machinery we've seen. It's the right-tilt version of Delta's magnificent Unisaw, and everything from the motor to the finely machined T-slots is nothing but the highest standard. Take the motor, for example: It's a 3-HP, single phase 230-volt with full-voltage starter. It flawlessly powers a positive-traction, three-belt V-drive that runs between two massive lifetime ball bearings for no--and we mean zero--vibration. The table is cast-iron, smooth as glass, along with two cast-iron extension wings and a beautifully laminated table supported by rock-solid, leveler-footed steel legs. Riding along the huge 76-by-27-inch table surface is a 50-inch Biesemeyer fence; there's none better, period. It's ruggedly built of nine-ply Finland birch and high-impact laminate that's hand-fitted to solid steel angle iron and tubing and glides and locks like a dream. The three-point locking system, built-in steel tape and hairline pointer assure accuracy to within 1/64-inch, even at its maximum 50 inches to the right of the blade. Even the arbor is a piece of perfection, precision-ground, stress-proofed and flange-faced after production. Inside this 600-pound saw's cabinet is a clever slope that directs sawdust right to the 4-inch duct collector chute to eliminate clogging in the cabinet. Quality saws always have a T-slot for the miter gauge, and this one's no exception, allowing you to extend Delta's super-precise Auto-Set miter gauge far beyond the front edge without tip-out or instability on both sides of the 10-inch blade. The right-tilting arbor allows you a max cut of 2-1/8 inches at 45 degrees, putting big gorgeous bevels well within your reach. If it's precision, perfection and power you're after, this is the last saw you'll ever buy.--Kris Jensen-Van Heste

Delta 36-878 5 Horsepower Unisaw with 50" Biesemeyer and Low Voltage Control

Among serious woodworkers who demand top quality tools in their shop, there's no debating the desirability of a Delta Unisaw. It's one of the few cabinet-style table saws still made in the USA, and the benefits show up in the quality of the tool's workmanship and finish. The Unisaw's smooth operation can be traced to the widely spaced, massive trunions which are machined from fine-grained cast iron and are completely adjustable to ensure the best possible alignment. The heavy cast-iron table adds to the saw's stability and features a 3/8-by-3/4-inch T-slot on each side of the blade. Include the two extension wings and you have a generous cast-iron table surface of 36 by 27 inches.

The single-phase, 5-horsepower induction motor is housed in a dust-sealed, fan-cooled enclosure, and power is transferred smoothly and efficiently via a positive-traction three-belt V-drive system. The motor cover has handy storage slots for your miter gauge and table inserts, but more importantly, the inside is designed to maximize the airflow for dust collection and, in conjunction with the redesigned cabinet interior, funnel all the dust efficiently to the 4-inch dust port without a hitch.

This model comes with a 50-inch commercial Biesemeyer fence system and accompanying table board. While the basics of this popular fence design have been copied by competing saw and fence manufacturers, there's still nothing quite like the original. The Biesemeyer is made of the heaviest gauge steel we've seen on a T-square type fence, and the fence face itself is made of laminated 9-ply Finland birch, glued solidly in place--a construction method that eliminates warpage in the fence line that the bolts or screws used in competing systems can cause. The fence locks to the front guide rail using Biesemeyer's three-point locking system and automatically aligns the fence parallel to the blade when the lever is tightened down, providing reliable accuracy every time. --Brian Trinen

Delta 36-L51X-BC50 5HP Left Tilt Unisaw with Biesemeyer

A 5 year warranty, one of 4 free tools or a $50 rebate, up to $500 in accessories, & over $2000 in savings with X-treme savings book. Looking for a saw that will serve as the cornerstone for a high performance shop? Delta's fully-featured version of the classic Unisaw offers outstanding performance with a 5 hp single phase motor housed in a new-age computer designed cover with integral 4" dust connector standard for optimal dust collection. In addition to the two 10" cast-iron wings and the right extension table this unit also includes a premium Carbide-tipped industrial saw blade and a commercial grade 50" Biesemeyer fence system with adjustable steel support legs. Add it all up and you are getting the best an Industry has to offer.

Go to:
Delta Portable Tablesaws
Delta Contractor Tablesaws
Delta Cabinet Tablesaws